blob: 0e3923989e384847be877b8546e16931d1b7c07a (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
|
; ----------------------------------------------- ;
; ;
; PROFIBUS configuration ;
; ;
; This file configures a pyprofibus instance. ;
; ;
; ----------------------------------------------- ;
; General settings
[PROFIBUS]
; Enable/disable debug mode.
; 0 -> no debugging.
; 1 -> DP debugging.
; 2 -> DP and PHY debugging.
debug=1
; PHY protocol layer configuration
[PHY]
; The PHY layer driver type.
;type=serial
;type=fpga
type=dummy_slave
; Only for type=serial:
; The PHY device name/path.
; Can be a device like /dev/ttyS0 or /dev/ttyAMA0
dev=/dev/ttyS0
; Only for type=serial:
; Serial line flow control and handshaking
rtscts=False
dsrdtr=False
; Only for type=fpga:
; SPI bus (to PHY FPGA) configuration.
spiBus=0
spiCS=0
spiSpeedHz=2500000
; The Profibus on-wire baud rate.
;baud=9600
baud=19200
;baud=45450
;baud=93750
;baud=187500
;baud=500000
;baud=1500000
;baud=3000000
;baud=6000000
;baud=12000000
; FDL protocol layer configuration
[FDL]
; DP protocol layer configuration
[DP]
; The master device class. Either 1 or 2.
master_class=1
; The Profibus address of this device.
master_addr=2
; ---
; Slave configurations
; Add as many [SLAVE_xxx] sections as needed.
; ---
; First slave configuration
[SLAVE_0]
; Optional slave name. Will be stored in slaveConf.name and slaveDesc.name.
; pyprofibus does not use the name internally.
name=first
; This slave's Profibus address
addr=8
; The path to the GSD file.
gsd=../misc/dummy_modular.gsd
; Boolean: Sync mode enabled/available?
sync_mode=1
; Boolean: Freeze mode enabled/available?
freeze_mode=1
; 8 bit integer specifying the Profibus group ident mask.
group_mask=1
; This slave's watchdog timeout, in milliseconds.
watchdog_ms=300
; Module configuration.
; For each module plugged into the slave, add a module_xxx
; entry with the name of the module.
; The module name must match the name from the GSD file (approximately).
; The modules are used in the order of the index number.
module_0=dummy output module
module_1=dummy output module
module_2=dummy input module
; The number of output bytes this slave transmits to the
; master in Data_Exchange.
; This usually depends on the modules plugged into the slave.
output_size=2
; The number of input bytes this slave expects to receive
; in Data_Exchange.
; This usually depends on the modules plugged into the slave.
input_size=2
; Request and interpret a slave diagnosis every n Data_Exchange telegrams.
; n defaults to 0, which means: Never periodically request diagnosis.
; If periodic diagnosis is switched off, then diagnostic information will only be requested on faults.
; Note that input-only slaves (output_size=0) probably need a non-zero diag_period.
diag_period=0
; Second slave configuration
[SLAVE_1]
; Optional slave name. Will be stored in slaveConf.name and slaveDesc.name.
; pyprofibus does not use the name internally.
name=second
; This slave's Profibus address
addr=42
; The path to the GSD file.
gsd=../misc/dummy_modular.gsd
; Boolean: Sync mode enabled/available?
sync_mode=1
; Boolean: Freeze mode enabled/available?
freeze_mode=1
; 8 bit integer specifying the Profibus group ident mask.
group_mask=1
; This slave's watchdog timeout, in milliseconds.
watchdog_ms=300
; Module configuration.
; For each module plugged into the slave, add a module_xxx
; entry with the name of the module.
; The module name must match the name from the GSD file (approximately).
; The modules are used in the order of the index number.
module_0=dummy output module
module_1=dummy output module
module_2=dummy input module
; The number of output bytes this slave transmits to the
; master in Data_Exchange.
; This usually depends on the modules plugged into the slave.
output_size=2
; The number of input bytes this slave expects to receive
; in Data_Exchange.
; This usually depends on the modules plugged into the slave.
input_size=2
; Request and interpret a slave diagnosis every n Data_Exchange telegrams.
; n defaults to 0, which means: Never periodically request diagnosis.
; If periodic diagnosis is switched off, then diagnostic information will only be requested on faults.
; Note that input-only slaves (output_size=0) probably need a non-zero diag_period.
diag_period=0
|
