blob: f9dfcbc6e8ea31e415eeb859577e13b21682cbd3 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
|
Simple PWM controller
=====================
`https://bues.ch/cgit/simplepwm.git/ <https://bues.ch/cgit/simplepwm.git/>`_
Simplepwm is a small PWM brightness controller for LED lamps.
Microcontroller
===============
Simplepwm supports the following microcontrollers. Not all features are supported on all microcontrollers. See the table for details.
============================ =========== ============ ========= ========= ========= =========
.. ATMega-328P ATMega-88(P) ATTiny-85 ATTiny-45 ATTiny-25 ATTiny-13
============================ =========== ============ ========= ========= ========= =========
Number of analog pot. inputs 3 3 1 1 1 1
Number of PWM outputs 3 3 1 1 1 1
Power saving x x x
Battery voltage monitoring x x x
HSL color model x x
Remote control via UART x x
Settings in EEPROM x x
Debugging via UART x x
Firmware update via UART x x
============================ =========== ============ ========= ========= ========= =========
Hardware schematics
===================
Schematics for ATMega based setups: `schematics-atmega/simplepwm-atmega.pdf <schematics-atmega/simplepwm-atmega.pdf>`_
Schematics for ATTiny based setups: `schematics-attiny/simplepwm-attiny.pdf <schematics-attiny/simplepwm-attiny.pdf>`_
Prebuilt firmware images
========================
The release archives of simplepwm contain prebuilt `.hex` files for all supported microcontrollers in the `hex` directory. These hex files can be flashed directly to the microcontroller with a any tool of your choice (e.g. Atmel Studio or avrdude).
The corresponding fuse settings can be found in the file `fuses.txt` in the same directory.
Building the firmware
=====================
The firmware build needs the following tool chain:
* Unix-like operating system
* GNU make
* AVR GCC
* AVR Binutils
* avrdude
Run the following commands to build the firmware:
.. code:: sh
cd firmware
make DEV=t85
Please specify the target microcontroller using the DEV variable as shown above.
Valid values are:
=============== ===========
Microcontroller make option
=============== ===========
ATTiny 13 `DEV=t13`
ATTiny 25 `DEV=t25`
ATTiny 45 `DEV=t45`
ATTiny 85 `DEV=t85`
ATMega 88 `DEV=m88`
ATMega 88P `DEV=m88p`
ATMega 328P `DEV=m328p`
=============== ===========
Additional build options that can be passed to `make`:
=============== ====== ============== ================================================================
make option values default description
=============== ====== ============== ================================================================
CONF_PWMLIM 1-100 100 Limit the maximum PWM duty cycle to this percentage.
CONF_PWMINVERT 0-1 0 Invert the PWM output signal(s).
CONF_LOWSPFACT float 1.0 Correction factor for lower range PWM setpoint.
CONF_ADCINVERT 0-1 0 Invert the ADC input signal(s).
CONF_ADCHSL 0-1 depends on DEV Interpret the ADC input signals as HSL setpoints instead of RGB.
FEAT_HIGHRES 0-1 depends on DEV Higher resolution in very low PWM setpoint range.
FEAT_BATTERY 0-1 depends on DEV Battery voltage monitoring
FEAT_POWERSAVE 0-1 depends on DEV Power saving / deep sleep
FEAT_REMOTE 0-1 depends on DEV Remote control via UART
FEAT_EEPROM 0-1 depends on DEV Store settings to EEPROM
FEAT_BOOT 0-1 depends on DEV Enable bootloader and firmware updating via UART.
=============== ====== ============== ================================================================
Flashing the firmware after build
=================================
Run the following commands to flash the firmware to the target microcontroller:
.. code:: sh
cd firmware
make DEV=t85 print_fuses
make DEV=t85 write_fuses
make DEV=t85 write_mem
Or alternatively use any other of the available AVR flashing tools to program the .hex file and fuses.
License
=======
Copyright (c) 2018-2020 Michael Buesch <m@bues.ch>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
|
